Your Maytag Centennial washer is a reliable appliance. But sometimes, it can show strange codes. These are Maytag Centennial washer error codes. They tell you what’s wrong. Knowing these codes helps you fix problems fast. This guide will cover all key aspects of troubleshooting your washer. You can often solve issues yourself.
Table of Contents
Why Your Maytag Centennial Washer Shows Errors
Maytag Centennial washers are designed with smart systems. These systems detect issues. When something is not right, an error code appears. This saves your washer from damage. It also helps you pinpoint the problem. Error codes can relate to water supply, drainage, motor, lid, or other parts.
Common Maytag Centennial Washer Error Codes and Solutions
Let’s look at the most frequent error codes. We’ll explain what they mean and how to fix them.
Water-Related Errors
These codes often point to issues with water entering or leaving the washer.
Error Code | Meaning | Common Causes | Simple Solution |
|---|---|---|---|
LF, Lo FL, F8 E1 | Long Fill Time / Low Water Flow | – Water supply off/restricted – Kinked inlet hoses – Clogged inlet screens – Water pressure issues | – Check water faucets (hot & cold) – Straighten kinked hoses – Clean inlet screens – Ensure adequate water pressure |
Drn, F9 E1 | Drain Issue / Long Drain Time | – Kinked drain hose – Clogged drain pump filter – Drain hose too high – Excessive suds | – Straighten drain hose – Clean drain pump filter – Adjust drain hose height (39-96 inches from floor) – Use HE detergent, reduce suds |
Sud, Sd | Excessive Suds | – Too much detergent – Non-HE detergent – Restricted drain hose | – Use only HE detergent – Reduce detergent amount – Check drain hose for kinks/clogs |
HC, F3 E2 | Hot/Cold Hoses Reversed | – Hot water hose connected to cold inlet – Cold water hose connected to hot inlet | – Turn off water supply – Reverse hot and cold inlet hoses |
Lid and Lock Errors
The lid lock is a safety feature. Problems here will stop your washer from running.
Error Code | Meaning | Common Causes | Simple Solution |
|---|---|---|---|
LdL | Lid Cannot Lock | – Obstruction under lid – Detergent buildup around lock – Faulty lid lock mechanism | – Check for items blocking lid – Clean lid lock area – Ensure lid closes completely – Press and hold Start button (up to 3 seconds) |
LdU | Lid Cannot Unlock | – Objects on top of lid – Cycle not finished – Control glitch | – Remove items from lid – Allow cycle to complete – Power cycle the washer (unplug for 5 minutes) |
F5 E2 | Door Not Locking Properly (Front Load) | – Obstruction in door lock – Misaligned door | – Check for items blocking door – Ensure door closes completely – Press Pause/Cancel twice, then Power once |
Motor and System Errors
These codes suggest issues with the washer’s internal operations or motor.
Error Code | Meaning | Common Causes | Simple Solution |
|---|---|---|---|
F7 E1 | Motor Speed Sensing Error | – Shipping bolts not removed – Overloaded washer – Loose/damaged wiring to motor – Faulty motor control board/actuator | – Remove all shipping bolts and spacers – Reduce load size – Inspect wiring (unplug first!) – May require professional service |
Ofb | Out of Balance Load | – Uneven load distribution – Washing single bulky items – Uneven washer | – Redistribute clothes evenly – Balance single items with towels – Ensure washer is level |
OL | Oversized Load | – Too many items in washer | – Remove some items – Restart cycle |
PF | Power Failure | – Interruption in power supply | – Touch and hold START to restart – Press POWER to clear code |
F#, E# or F## | General System Error | – Computer motherboard glitch – Sensor issue | – Press START/PAUSE to clear – Power cycle the washer (unplug for 5 minutes) – If persistent, professional help needed |
Entering Diagnostic Mode
Your Maytag Centennial washer has a diagnostic mode. This can help you find error codes or test components.
- Ensure Washer is Off: Make sure the washer is plugged in but off.
- Cycle Selector Knob: Place the cycle selector knob at the 12 o’clock position (or “Normal” depending on your model).
- Sequence of Turns: Perform this sequence using the cycle selector knob quickly:
- One click to the LEFT
- Three clicks to the RIGHT
- One click to the LEFT
- One click to the RIGHT
- Confirmation: All lights should illuminate except the “Lid Lock” light. This means you are in diagnostic mode.
- Reading Codes: In diagnostic mode, you can often cycle through stored error codes. Your owner’s manual will have specific instructions for your model on how to read these codes.
Troubleshooting Tips
- Always Unplug: Before checking any internal parts, always unplug your washer from the power outlet. This is for your safety.
- Owner’s Manual: Your owner’s manual is your best friend. It has specific error codes and troubleshooting steps for your exact model.
- Don’t Overload: Overloading is a common cause of errors. It stresses the motor and balance system.
- Use HE Detergent: Maytag Centennial washers are designed for High-Efficiency (HE) detergent. Using too much or non-HE detergent causes excessive suds, leading to errors.
- Check Hoses: Regularly inspect inlet and drain hoses for kinks, clogs, or damage.
- Level Your Washer: An unlevel washer can cause vibration and “out of balance” errors. Use a level tool to ensure it sits flat.
- Power Cycle: Sometimes, a simple power cycle (unplugging the washer for 5 minutes) can clear temporary error codes.
FAQ
My Maytag Centennial washer displays “LdL.” What should I do?
The “LdL” code means the lid is not locking. First, check for anything blocking the lid from closing fully. This could be a stray sock or lint. Also, look for detergent buildup around the lid lock mechanism. Ensure the lid striker (the part on the lid that fits into the lock) is clean and unobstructed. If nothing is blocking it, press and hold the Start button for up to three seconds to try and engage the lock.
What does “F7 E1” mean on my Maytag Centennial washer?
The “F7 E1” error code indicates a motor speed sensing error. This means the washer’s motor isn’t reaching the correct speed. Common causes include shipping bolts not being removed (if it’s a new installation), an overloaded washer, loose wiring to the motor, or a problem with the motor itself or the motor control board. Start by checking for shipping bolts and reducing the load size. If the problem persists, it may require professional inspection.
My washer shows “Drn” or “F9 E1.” How can I fix this?
Both “Drn” and “F9 E1” point to a draining issue or excessively long drain time. First, check the drain hose at the back of the washer. Make sure it’s not kinked or clogged. The drain hose should be properly installed, typically between 39 and 96 inches above the floor. Also, excessive suds from too much or incorrect detergent can slow down draining. Ensure you are using HE detergent and the correct amount. You may need to clean the drain pump filter, if accessible on your model.
Can I reset my Maytag Centennial washer to clear an error code?
Yes, often you can. The simplest way to reset your washer is to perform a “power cycle.” Unplug the washer from the electrical outlet for at least 5 minutes. Then, plug it back in. This can clear temporary glitches in the control board and resolve some error codes. For more persistent codes, entering diagnostic mode as described in the article can help identify specific issues.
Why is my Maytag Centennial washer shaking violently during the spin cycle and showing “Ofb”?
The “Ofb” error means the load is out of balance. This is common when washing bulky items like blankets or only a few heavy items. The washer tries to correct an unbalanced load. If it can’t, it will display this code and may stop. To fix this, open the lid, redistribute the clothes evenly around the wash plate, and close the lid. Avoid washing a single heavy item; add a few towels to balance the load. Also, ensure your washer is sitting on a level surface.
Bottom Line
Understanding Maytag Centennial washer error codes empowers you to diagnose and often fix common washer problems. By following these simple steps, you can save time and money. Remember safety first, and always consult your manual.
